A2b ETX-200 Installation Guide

11INSTALLATIONGUIDEETX-200DVB-T Terrestrial Processordesign for TVEnglish

10104.3.4 Output settingsASI modeThe output selection ASI disables all RF modulation on the outputs and all selected services will be transmitted only

11114.3.5 Analogue mode (cont.)It is possible to select scaling of the picture format to fit with connected TV-sets. This is handled in the [Aspect ra

12124 Settings (continued)4.3.5 Service ManagementThe Service management menu gives an overview of available services from antenna input or the ASI i

1313The ASI output contains the services you have selected for [Digital output].For decryption you mark the service by a click on the service name lin

14144.3.6 UploadUpdate of the ETX-200 firmware or upload of enhanced functionality is done via the Upload menu. NOTE! Always read the Instructions car

15154.2.6 IPTV output (SW option)This menu allows for settingsrequired to transmit a digital-TV transport stream as IPTV. IPTV output is optional and

1616English16To be sure that you don’t exceed maximum bit rate for an output MUX, please control that you don’t select to many services. The table be

1717The ETX-200 can be installed either as a stand alone unit (Wall mount plate) or in base unit (EBU-100).Before connecting power to the ETX-200, mak

18186.1.2 Installation of 3 pcs of ETX-200 and one QAM mux out.6.1 Installation examples6.1.1 Installation of 3 pcs of ETX-200 and one COFDM mux out.N

19196.1.3 Installation of ETX-200 units through a switch with DHCP with possibility for remote management over VPN connection between office and Hea

22Contents1. Introduction2. Unpacking the unit3. Connections and indications4. Settings5. About remultiplexing6. Installation7. SW options8. SNMP9. Te

207 SW optionsIt’s possible to upgrade your ETX-200 with one or more SW options. Below you can read about available optons. For price list, contact y

217.8 EXM-CL, CryptoLITEThis SW option allows you to encrypt channels out in Cryptoguard in a muxwithout any need for an encryption server. For more i

227.9 EXM-SC, SimulcryptThis SW option allows you to encrypt a Mux in an EXM unit. When this SW option is uploaded to the unit a new menu will appear

237 SW options (continued)7.9 EXM-SC, Simulcrypt (cont.)The setup of encryption of services with Simulcrypt is described below:1. Make the necessary

248 SNMPWith the FW 1.2 in the ETX-200 you are able to use the SNMP Interface for monitoring the ETX-200. To get the SNMP menu on the unit you write

2525ETX-200 DVB-T Terrestrial processorThis specification may change without prior notice.MiscellaneousPower supply 7,5 VDC nom. (6-10 VDC)Power consu

2626This specification may change without prior notice.MPEG Decoder - AudioSupported formats MPEG 1 layer II, AAC HE,Output Selection of Dual

272710 Declaration of ConformityThe document for Declaration of Conformity you will find at www.a2b.se.Further information at www.a2b.se.English

28282811 GlossaryEnglishDVB Digital Video Broadcasting (Standardization body)MPEG-2 Compression format for digital TVMPEG-4 Compression format for di

29EnglishNotes________________________________________________________________________________________________________________________________________

331 IntroductionThank you for purchasing an A2B Electronics product. The ETX-200 is a revolutionary solution for reception and modification of terres

30EnglishNotes________________________________________________________________________________________________________________________________________

31EnglishNotes________________________________________________________________________________________________________________________________________

3232www.a2b.seA2B Electronics ABSödra Allén 23-25, 591 37 MotalaP.O. Box 14, 591 21 MotalaSWEDENPhone +46 141 229100Fax +46 141 229101E-mail market@a2

44Following components are included in the package:Amount Description1 ETX-200 Terrestrial Processor1 Installation guide2 Front panel screwsNOTE! Ther

55Common Interface Insert your Common Interface ConditionalAccess module into this slotPower on indicator Green light indicates that power is on.Rx er

66A/V out *) Connection for monitoring or to an RF modulator.ASI in *) Input for ASI (Asynchronous Serial Interface) for high speed transport stream r

774.1 TCP/IP settings for Windows XP (setting your PC to 192.168.0.19)Click ”Start”, select ”Control panel” and select ”Network connections” and then

884.3 EXM Web Control Interface4.3.1 System menuThe following [System] menushould appear when you connectto the ETX-200. The [System]menu contains bas

99IP address settings (continued)Setting new static IP address in the ETX-200Connect your PC to each EXM unit after that you have done all other setti